What are your thoughts and feelings on How to Install a Bathtub Yourself?
Setting up a tub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging task. If the old bathtub is easily easily accessible, the job can relocate quickly; if you need to open up a wall to get rid of the old tub as well as place the new bath tub, the job is much harder. In either situation, the job is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have certified yourself for the task as well as fit trying it. Rather than hiring a contractor to take control of a halfway-completed project, it is far better to take into consideration employing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This short article will certainly help you install a brand-new tub in your restroom if you have actually already acquired a new bathtub as well as do not need to transform the arrangement of your previous water supply pipes.
Your devices as well as product list need to consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipelines. When the supply pipes have actually been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washers remain in area in between the tap as well as the sink. Secure the tap in position with the manufacturer provided backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous type should be linked to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Tub
Utilizing the two wood boards under its feet, put the bathtub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by examining the level as well as readjusting the feet on the tub up until the spirit level reads degree.
To install taps, fit the bottom of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the supply of water as well as check all joints and also new pipework for leakages as well as tighten them if required. Load the tub as well as additionally inspect the overflow electrical outlet and also the regular outlet for leakages.
Lastly, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait until the bath tub has actually been used at least once as this will settle it into its last position.
Preparing for the Setup
First of all, the supporting frame supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to prevent strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its final placement.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill the bath tub with water before sealing, to allow for the motion experienced when the bathtub remains in use. The sealant can crack rather early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the ceramic tiles using water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very taken with Tools You Need to Install a New Bathtub and I'm hoping you enjoyed reading the new page. Do you know about somebody else who is fascinated with the subject? Feel free to share it. Thanks so much for your time invested reading it.
Book Appointment Now